|
346868656
|
0420600
|
2023-07-19
|
10500 47TH ST N, CLEARWATER, FL, 33762
|
|
| Inspection Type |
Referral
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2023-07-19
|
| Emphasis |
L: FORKLIFT
|
| Case Closed |
2024-01-08
|
Related Activity
| Type |
Referral |
| Activity Nr |
2050296 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Other |
| Standard Cited |
19100147 C04 II |
| Issuance Date |
2023-12-15 |
| Current Penalty |
4465.0 |
| Initial Penalty |
4465.0 |
| Final Order |
2024-01-08 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Related Event Code (REC) |
Referral |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(ii):Procedures did not clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy, and the means to enforce compliance including, but not limited to, 29 CFR 1910.147(c)(4)(ii)(A), (c)(4)(ii)(B), (c)(4)(ii)(C) and (c)(4)(ii)(D): a) At facility located at 10500 47th St N in Clearwater, FL; As observed on or about July 19, 2023, the VAC Machine F procedure utilized by employees during the thermoforming mold board removal did not include the purpose of the procedure, prior initiation of the procedures, name and job titles of affected employees and how to notify prior initiation of the procedures, gravitational energy as an energy source, the hazards associated to each energy source and the means to enforce compliance, exposing employees to crushed-by hazards. |
|
|
|
343806980
|
0420600
|
2019-02-22
|
10500 47TH STREET NORTH, CLEARWATER, FL, 33762
|
|
| Inspection Type |
Complaint
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2019-02-22
|
| Case Closed |
2019-08-26
|
Related Activity
| Type |
Complaint |
| Activity Nr |
1427200 |
| Safety |
Yes |
|
| Type |
Inspection |
| Activity Nr |
1412373 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Repeat |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2019-07-24 |
| Abatement Due Date |
2019-08-05 |
| Current Penalty |
5114.5 |
| Initial Penalty |
10229.0 |
| Final Order |
2019-08-20 |
| Nr Instances |
1 |
| Nr Exposed |
25 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: (a) On or about 2/22/2019, energy control procedures for equipment including, but not limited to, the horizontal band saw was not utilized for the performance of activities such as changing the blade, in that, a lockout device was not applied, exposing employees to an amputation hazard. The Proto, Corp. was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.147(c)(4)(i), which was contained in OSHA inspection number 1042785, citation number 02, item number 001 and was affirmed as a final order on 6/3/2015, with respect to a workplace located at 10500 47th Street N, Clearwater, FL 33762. |
|
| Citation ID |
01002 |
| Citaton Type |
Repeat |
| Standard Cited |
19100212 A03 II |
| Issuance Date |
2019-07-24 |
| Abatement Due Date |
2019-08-19 |
| Current Penalty |
8525.0 |
| Initial Penalty |
17050.0 |
| Final Order |
2019-08-20 |
| Nr Instances |
1 |
| Nr Exposed |
25 |
| Related Event Code (REC) |
Complaint |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(3)(ii): The point of operation of machines whose operation exposed an employee to injury, was not guarded: (a) On or about 2/22/2019, the adjustable guarding of the vertical band saws were faulty and not utilized, exposing employees to an amputation hazard. (b) On or about 2/22/2019, the blade of the horizontal band saws was inadequately guarded, exposing employees to an amputation hazard. The Proto, Corp. was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.212(a)(3)(ii), which was contained in OSHA inspection number 1042785, citation number 01, item number 002 and was affirmed as a final order on 6/3/2015, with respect to a workplace located at 10500 47th Street N, Clearwater, FL 33762. |
|
| Citation ID |
02001 |
| Citaton Type |
Other |
| Standard Cited |
19100219 C02 I |
| Issuance Date |
2019-07-24 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2019-08-20 |
| Nr Instances |
1 |
| Nr Exposed |
25 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: (a) Forrest 480P Horizontal Band Saw s/n F00783 - the rotating idler/tension shaft with an exposed length of 4 inches and 1.5-inch diameter was not guarded.; observed on or about 2/22/2019. |
|
|
|
340427855
|
0420600
|
2015-02-26
|
10500 47TH STREET NORTH, CLEARWATER, FL, 33762
|
|
| Inspection Type |
Complaint
|
| Scope |
Partial
|
| Safety/Health |
Health
|
| Close Conference |
2015-04-28
|
| Emphasis |
N: AMPUTATE, L: SILICA, L: FORKLIFT, N: DUSTEXPL, N: SILICA
|
| Case Closed |
2015-06-05
|
Related Activity
| Type |
Referral |
| Activity Nr |
965351 |
| Health |
Yes |
|
| Type |
Inspection |
| Activity Nr |
1046120 |
| Safety |
Yes |
|
| Type |
Complaint |
| Activity Nr |
963646 |
| Safety |
Yes |
| Health |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100212 A01 |
| Issuance Date |
2015-05-07 |
| Abatement Due Date |
2015-06-11 |
| Current Penalty |
2295.0 |
| Initial Penalty |
3825.0 |
| Final Order |
2015-06-03 |
| Nr Instances |
4 |
| Nr Exposed |
11 |
| Related Event Code (REC) |
Complaint |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a) Thermoform machine A - Inadequate guarding was present for the rotating table and closing platens, on or about March 13, 2015. b) Thermoform machine B - Inadequate guarding was present for the rotating table and closing platens, on or about March 13, 2015. c) Thermoform machine C - Inadequate guarding was present for the rotating table and closing platens, on or about March 13, 2015. d) Thermoform machine D - Inadequate guarding was present for the rotating table and closing platens, on or about March 13, 2015. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100212 A03 II |
| Issuance Date |
2015-05-07 |
| Abatement Due Date |
2015-06-11 |
| Current Penalty |
2295.0 |
| Initial Penalty |
3825.0 |
| Final Order |
2015-06-03 |
| Nr Instances |
3 |
| Nr Exposed |
8 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.212(a)(3)(ii): Points of operation of machinery were not guarded to prevent employees from having any part of their body in the danger zones during operating cycles: a) Extrusion Line A - The shear at the end of the line was unguarded, on or about March 13, 2015. b) Extrusion Line B - The shear at the end of the line was unguarded, on or about March 13, 2015. c) Extrusion Line C - The shear at the end of the line was unguarded, on or about March 13, 2015. |
|
| Citation ID |
02001 |
| Citaton Type |
Other |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2015-05-07 |
| Abatement Due Date |
2015-06-03 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-06-03 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) In-Line Area - The lockout tagout procedure for the Brown in-line machine was not documented, on or about March 13, 2015. |
|
|
